Auteur Sujet: Mise en route LEOX LXT-010H-D  (Lu 80358 fois)

0 Membres et 2 Invités sur ce sujet

cyayon

  • Abonné Orange Fibre
  • *
  • Messages: 656
  • Cordon 74 - Orange Fibre Pro
Mise en route LEOX LXT-010H-D
« Réponse #144 le: 21 septembre 2022 à 15:25:32 »
HW_HWVER is one of 2 parameters used to sent to OLT, so operator can recognize what hardware model it is.

Changing HW_HWVER might have such implication, that OLT may have firmware upgrade rules based on HW_HWVER.
So OLT might try to enforce firmware upgrades, that will not succeed, but will initiate reboots..

Marcin

Hi Marcin,

Thanks for your answer !
You recommend to NOT change HW_HWVER unless it is mandatory if i understand correctly ?
It seems that Orange require this parameter, or i am wrong ?

Do you have commands list for this new ONT ? gtop seems to not exist.

thanks.

marcinkuczera

  • Abonné FAI autre
  • *
  • Messages: 68
  • Pologne
Mise en route LEOX LXT-010H-D
« Réponse #145 le: 21 septembre 2022 à 15:30:06 »
You recommend to NOT change HW_HWVER unless it is mandatory if i understand correctly ?

Right

Citer
It seems that Orange require this parameter, or i am wrong ?
Orange uses different systems and configurations depending on country, OLTs, business logic and so on.
I can't say how it is in other countries. In Poland (Orange-Poland) - it is not necessary to do it.

Citer
Do you have commands list for this new ONT ? gtop seems to not exist..
again, this interface is not normally used from telco perspective, it is only for debug/development.

hit TAB twice, you will see available commands from busybox level

Marcin

cyayon

  • Abonné Orange Fibre
  • *
  • Messages: 656
  • Cordon 74 - Orange Fibre Pro
Mise en route LEOX LXT-010H-D
« Réponse #146 le: 21 septembre 2022 à 15:32:17 »
Thanks !

gtop seems to no more exist, do you have an alternative command please ?


marcinkuczera

  • Abonné FAI autre
  • *
  • Messages: 68
  • Pologne
Mise en route LEOX LXT-010H-D
« Réponse #147 le: 21 septembre 2022 à 15:42:56 »
Thanks !

gtop seems to no more exist, do you have an alternative command please ?

Nope, I have stripped image to make it small. It is important when you consider massive upgrade..

cyayon

  • Abonné Orange Fibre
  • *
  • Messages: 656
  • Cordon 74 - Orange Fibre Pro
Mise en route LEOX LXT-010H-D
« Réponse #148 le: 21 septembre 2022 à 15:45:45 »
thanks, i understand


Sinon, pour tous les autres, essayez de NE PAS modifier le HW_HWVER et voir si ca monte quand même. La valeur par défaut est LXT-010H-D.

Moi j'ai utilisé  HWTCA240FA (mon ONT Huawei) au lieu du standard habituel (il semble) SMBSSGLBF121 et tout fonctionne.
Quelque chose me dit que ce n'est pas nécessaire.

Faites le test...

Mackila

  • Abonné Bbox fibre
  • *
  • Messages: 354
  • 33
Mise en route LEOX LXT-010H-D
« Réponse #149 le: 21 septembre 2022 à 15:53:01 »
Only changed GPON_SN and PON_VENDOR_ID
flash set GPON_SN SMBSXXXXXXXX
flash set PON_VENDOR_ID SMBS

Then went from
CCR2004 SFP+1 <- DAC -> CRS305 with FS.com ONU
to
CCR2004 SFP+1 <- S+RJ10 -> Leox

All work fine.

Bouygues 2000/800 "Ultym" (now advertised as "2000/900")

   Speedtest by Ookla

     Server: LaFibre.info - Bordeaux (id = 21415)
        ISP: Bouygues Telecom
    Latency:     2.40 ms   (0.17 ms jitter)
   Download:  1949.99 Mbps (data used: 1.5 GB )
     Upload:   877.92 Mbps (data used: 1.1 GB )
Packet Loss:     0.0%

cyayon

  • Abonné Orange Fibre
  • *
  • Messages: 656
  • Cordon 74 - Orange Fibre Pro
Mise en route LEOX LXT-010H-D
« Réponse #150 le: 21 septembre 2022 à 15:55:13 »
Only changed GPON_SN and PON_VENDOR_ID
flash set GPON_SN SMBSXXXXXXXX
flash set PON_VENDOR_ID SMBS

Then went from
CCR2004 SFP+1 <- DAC -> CRS305 with FS.com ONU
to
CCR2004 SFP+1 <- S+RJ10 -> Leox

All work fine.

Bouygues 2000/800 "Ultym" (now advertised as "2000/900")

   Speedtest by Ookla

     Server: LaFibre.info - Bordeaux (id = 21415)
        ISP: Bouygues Telecom
    Latency:     2.40 ms   (0.17 ms jitter)
   Download:  1949.99 Mbps (data used: 1.5 GB )
     Upload:   877.92 Mbps (data used: 1.1 GB )
Packet Loss:     0.0%

Je viens de tester chez Orange, j'ai remis la valeur par défaut, ca fonctionne toujours.

donc pas besoin de toucher à ça.
Merci !

rooot

  • Abonné RED by SFR fibre FttH
  • *
  • Messages: 1 952
  • 🔵🔵🔵🔵⚪⚪⚪⚪🔴🔴🔴🔴
Mise en route LEOX LXT-010H-D
« Réponse #151 le: 21 septembre 2022 à 18:01:16 »
hi Marcin, just received my LXT-010H-D,
same behavior as with the vsol. i'm geting O5 but everything freeze after a few seconds, i lose access to the web interface, to telnet, and after a few minutes the onu seem to restart.
what can i do ?


Changing HW_HWVER might have such implication, that OLT may have firmware upgrade rules based on HW_HWVER.
So OLT might try to enforce firmware upgrades, that will not succeed, but will initiate reboots..
could this be the reason why my ONU is rebooting ? as i didn't touch this setting, maybe it's the reason i'm having these problems since the begining?

hwti

  • Abonné Orange Fibre
  • *
  • Messages: 2 237
  • Chambly (60)
Mise en route LEOX LXT-010H-D
« Réponse #152 le: 21 septembre 2022 à 22:45:08 »
HW_HWVER is one of 2 parameters used to sent to OLT, so operator can recognize what hardware model it is.

Changing HW_HWVER might have such implication, that OLT may have firmware upgrade rules based on HW_HWVER.
So OLT might try to enforce firmware upgrades, that will not succeed, but will initiate reboots..
For Orange France, as far as we know :
 - HWTC OLTs : no need to change the hardware version
 - ALCL OLTs : the hardware version needs to match one of the known ONTs

zakhounet

  • Abonné Orange Fibre
  • *
  • Messages: 23
  • Jonage 69330
Mise en route LEOX LXT-010H-D
« Réponse #153 le: 21 septembre 2022 à 23:53:03 »
Bonjour,

Pensez-vous que l'utilisation du Leox LXT-010 soit aussi possible pour remplacer une live box 6 ?

cyayon

  • Abonné Orange Fibre
  • *
  • Messages: 656
  • Cordon 74 - Orange Fibre Pro
Mise en route LEOX LXT-010H-D
« Réponse #154 le: 22 septembre 2022 à 01:30:32 »
For Orange France, as far as we know :
 - HWTC OLTs : no need to change the hardware version
 - ALCL OLTs : the hardware version needs to match one of the known ONTs

Hi,

Very interesting information, thanks !
In the same way, do you know why dhcp COS6 is mandatory in some regions and not in others ?
Is there a plan for Orange France to change this behavior globally ?

akeix

  • Abonné Bbox fibre
  • *
  • Messages: 158
  • Bourges (18)
    • Passion d'images
Mise en route LEOX LXT-010H-D
« Réponse #155 le: 22 septembre 2022 à 06:46:51 »
Est-ce que tu as vérifié avec iperf3 en UDP (par exemple "iperf3 -c speedtest.milkywan.fr -p 9201 -u -b 400M") pour voir de quelle ampleur sont les pertes ?
Qu'est-ce que tu as comme valeur pour OMCI_WAN_QOS_QUEUE_NUM sur le LEOX ?

Je n'ai pas eu le temps de faire le tests iperf3 (Le reste de la famille jouait ou regardé Netflix  ;D ).
J'ai vérifié la valeur OMCI_WAN_QOS_QUEUE_NUM qui est bien à 4.

For Orange France, as far as we know :
 - HWTC OLTs : no need to change the hardware version
 - ALCL OLTs : the hardware version needs to match one of the known ONTs

Du coup, chez moi (Bourges), j'ai du changer la valeur de HW_HWVER. Donc je dois être sur un OLT Alcatel.
Sans changer cette valeur, le leox passe bien au statut "O5" mais la livebox ne se connecte pas.

J'ai donc passé les commandes suivantes :
  • flash set GPON_SN ARLTxxxxxxxx
  • flash set PON_VENDOR_ID ARLT
  • flash set HW_HWVER ARLTyyyyyyyy

J'ai bien sur récupéré ses informations sur la page ONT de la livebox 5.
Ce qui me surprend, vous êtes nombreux à avoir un numéro de série commençant pas SMBS contrairement à moi.

Sur le LEOX, il y a mode compatibilité avec les choix suivants : Défaut (c'est le mode sélectionné), Huawei, ZTE et Custom.
Vous savez si cela peu jouer sur mon problème ?

Normalement, je dois recevoir le LEOX  LXT-010H-D aujourd'hui ou demain.
Je verrai si j'ai le même comportement.