Bonjour,
Je suis chez BT et je souhaite remplacer la bbox Fast 5688b comme suit :
SCAPC --> G 010S A --> ES16XG --> UDM PRO (Je me suis inspiré de la réussite de florian)
Autant prévenir Je ne suis pas un pro du réseau mais les diverses lectures sur ce forum aussi bien dans l’univers BT qu’Orange sont une véritable mine d’or et m’ont appris énormément car je pars de quasi 0 (juste de la débrouille et du bricolage 😊 ).
Juste vs me pardonnerez si j’ai loupé un truc car ttes les infos engrangées ont plutôt tendance à se mélanger là-haut 😊
Enfin je me suis donc équipé en conséquence (non mais !!! un noob qui veut du pro sortez le 😊) et tenté de suivre les tutos, mais là je bloque sur l’ont G-010S-A :
Il oscille en current_state entre 02 et 05 (j’ai lu le guide de Gnubyte qui a fait un boulot hors norme
https://lafibre.info/remplacer-livebox/guide-de-connexion-fibre-directement-sur-un-routeur-voire-meme-en-2gbps/Et les liens associés
https://forum.huawei.com/carrier/en/thread-446043-1-1.html, mais cela reste un peu de haut niveau pour moi), j’en déduirais tout de même que cet état dépendrais peut être de la compatibilité avec l’OLT……. ou peut-être des SLID, ID, ou SN que j’ai mal renseigné)
Donc voilà ce que j’ai renseigné sur le G-010S-A :
Via l'interface http :
Enregistrement du SLID : (00000 + imei) --> imei récupéré sur l'étiquette de la BBOX (15chiffres)
quand je me relogg en http je retrouve bien mon (00000 + imei)Via l'interface SSH du G010S A:
Enregistrement du ID et SN (SMBSxxxxxxxx)
ritool set MfrID SMBS --> 4 premiers caractères du SN lu sur l'interface de la BBOX et rentré tel-quel
ritool set G984Serial 12345678 --> 8 derniers chiffres du SN lu sur l'interface de la BBOX et rentré tel-quel
relecture sur l'onu tjrs via ssh:
ONTUSER@SFP:~# onu gtcsng
errorcode=0 serial_number="83 xx xx xx 2 xx xx 223" Ré-enregistrement du PLOAM password (SLID)
Uci set gpon.ploam.nPassword=’0x30 0x30 …….. ‘ correspondant aux 20 chiffres (00000 + imei) à savoir si j’ai bien traduit tout ça ….. exemple pour un chiffre 9 = 0x39……. et c……
relecture sur l'onu tjrs via ssh:
ONTUSER@SFP:~# onu gtccg
errorcode=0 bip_error_interval=4095 sf_threshold=5 sd_threshold=9
serial_number_request_threshold=10 rogue_msg_id_upstream_reset=255
rogue_msg_repeat_upstream_reset=3 rogue_msg_id_device_reset=255
rogue_msg_repeat_device_reset=3 rogue_msg_enable=0
ploam_timeout_1=11000 ploam_timeout_2=100 emergency_stop_state=0
password="48 48 48 48 48 48 48 48 48 48"Je n'ai pas rentré l @ mac de la BBOX……..
Les autres données que j’ai réussi à obtenir sur l’ont sont les suivantes :
---------------------------------------------------------------------
Lantiq GPON Evaluation System (SFP), Image Revision 7.5.3
----------------------------------------------------------------------
IFXOS, Version 1.6.6
FALC(tm) ON Base Driver, Version 7.5.1.0 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
FALC(tm) ON Optic Driver, version 7.5.1.0 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
/opt/lantiq/bin/show_version.sh: line 21: OperatorID: not found
GPON ONU control, version 7.5.1.0 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
GPON Optic Control, version 7.5.1.0 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
GPON ONU top, version 7.5.1.0 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
OMCI Simulate, version 7.5.1 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
OMCI daemon, version 7.5.1 (c) Copyright 2015, Lantiq Beteiligungs-GmbH Co. KG
GPON Optic top, version 7.5.1.0 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
GPON Optic Calibration CLI, version 7.5.1 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
GPON Exception Dump Tool, version 7.5.1.0 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
OMCI usock server, version 7.5.1 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
ONTUSER@SFP:~# cat /usr/etc/buildinfo
ONT_TYPE=g010sa
PON_MODE=GPON
SOFTWAREVERSION=BFG.A06p02
PRODUCTCLASS=g010sa
RELEASE=0.0.0
BUILDSTAMP=
BUILDDATE=20170407_1757
COPYRIGHT=ASB
WHOBUILD=buildmgr
IMAGEVERSION=3FE46398BFGA06
VOIP=
CONFIG_VOIP_SW=
LATEST_REV=18511
REPO=sw
SIGN=n
Pour le 2.5gb/s : C’est OK sur l’interface de l’ES16XG
Je découvre il y a qqs instants dans l’interface web de la BBOX dans l’onglet fibre que l’OLT est HWTC donc au final je me pose la question de savoir si l’ont G-010S-A est bien compatible avec cet OLT ? ce qui expliquerait ce qui est dit plus hautEnfin voilà ou j’en suis mais je tourne en boucle, un peu d’aide serait la bienvenue et super sympa de votre part ou du moins me ré aiguiller sur la bonne voie ou me dire quel matériel aurait le plus de succès......
Je tenterais bien le 18 mais je ne sais pas si ça serait apprécié 😊
D’avance merci
a+++