Mon ER-X est connecté soit au MC220L soit au switch GS108Tv2
Bon ben je galère à déterminer l'erreur (j'ai censuré):
sudo dibbler-client run
| Dibbler - a portable DHCPv6, version 1.0.1 (CLIENT, Linux port)
| Authors : Tomasz Mrugalski<thomson(at)klub.com.pl>,Marek Senderski<msend(at)o2.pl>
| Licence : GNU GPL v2 only. Developed at Gdansk University of Technology.
| Homepage: http://klub.com.pl/dhcpv6/
2018.09.09 18:40:45 Client Notice My pid (2876) is stored in /var/lib/dibbler/client.pid
2018.09.09 18:40:45 Client Notice Detected iface eth0.832/10, MAC=78:8a:20:.
2018.09.09 18:40:45 Client Notice Detected iface eth0.840/9, MAC=78:8a:20:.
2018.09.09 18:40:45 Client Notice Detected iface eth4/8, MAC=78:8a:20:.
2018.09.09 18:40:45 Client Notice Detected iface eth3/7, MAC=78:8a:20:.
2018.09.09 18:40:45 Client Notice Detected iface eth2/6, MAC=78:8a:20:.
2018.09.09 18:40:45 Client Notice Detected iface eth1/5, MAC=78:8a:20:.
2018.09.09 18:40:45 Client Notice Detected iface eth0/4, MAC=78:8a:20:.
2018.09.09 18:40:45 Client Notice Detected iface imq0/3, MAC=.
2018.09.09 18:40:45 Client Notice Detected iface switch0/2, MAC=78:8a:20:.
2018.09.09 18:40:45 Client Notice Detected iface lo/1, MAC=00:00:00:00:00:00.
2018.09.09 18:40:45 Client Notice Parsing /etc/dibbler/client.conf config file...
2018.09.09 18:40:45 Client Debug PD: Following interfaces marked as downlink: none
2018.09.09 18:40:45 Client Debug Prefix delegation option (no parameters) found.
2018.09.09 18:40:45 Client Debug Will send option 16 (hex data, len11)
2018.09.09 18:40:45 Client Debug Will send option 15 (hex data, len45)
2018.09.09 18:40:45 Client Debug Will send option 11 (hex data, len22)
2018.09.09 18:40:45 Client Debug Will send option 11 (hex data, len22)
2018.09.09 18:40:45 Client Debug Parsing /etc/dibbler/client.conf done, result=0(success)
2018.09.09 18:40:45 Client Debug 1 interface(s) specified in /etc/dibbler/client.conf
2018.09.09 18:40:45 Client Info Interface eth0.832/10 configuration has been loaded.
2018.09.09 18:40:45 Client Debug DUID's value = 00:01:00:01:23:27:fe:e7:78: was loaded from client-duid file.
2018.09.09 18:40:45 Client Info My DUID is 00:01:00:01:23:27:fe:e7:78:8a:.
2018.09.09 18:40:45 Client Info Loading old address database (client-AddrMgr.xml), using built-in routines.
2018.09.09 18:40:45 Client Info DB timestamp:1536511241, now()=1536511245, db is 4 second(s) old.
2018.09.09 18:40:45 Client Debug Auth: Replay detection value loaded 0
2018.09.09 18:40:45 Client Info All client's 00:01:00:01:23:27:fe:e7:78:8a: leases are not valid.
2018.09.09 18:40:45 Client Debug Bind reuse enabled (multiple instances allowed).
2018.09.09 18:40:45 Client Notice Creating control (::) socket on the lo/1 interface.
2018.09.09 18:40:45 Client Notice Creating socket (addr=fe80::7a8a:20ff:) on eth0.832/10 interface.
2018.09.09 18:40:45 Client Debug Initialising link-state detection for interfaces: eth0.832/10
2018.09.09 18:40:45 Client Notice CONFIRM support compiled in.
2018.09.09 18:40:45 Client Info Creating SOLICIT message with 0 IA(s), no TA and 1 PD(s) on eth0.832/10 interface.
2018.09.09 18:40:45 Client Error AUTH: protocol 6529048 not supported yet.
2018.09.09 18:40:45 Client Debug Sending SOLICIT(opts:1 25 8 16 15 11 11 6 ) on eth0.832/10 to multicast.
2018.09.09 18:40:45 Client Debug Sleeping for 1 second(s).
2018.09.09 18:40:46 Client Info Processing msg (SOLICIT,transID=0x6359e9,opts: 1 25 8 16 15 11 11 6)
2018.09.09 18:40:46 Client Error AUTH: protocol 6529048 not supported yet.
2018.09.09 18:40:46 Client Debug Sending SOLICIT(opts:1 25 8 16 15 11 11 6 ) on eth0.832/10 to multicast.
2018.09.09 18:40:46 Client Debug Sleeping for 2 second(s).
2018.09.09 18:40:48 Client Info Processing msg (SOLICIT,transID=0x6359e9,opts: 1 25 8 16 15 11 11 6)
2018.09.09 18:40:48 Client Error AUTH: protocol 6529048 not supported yet.
2018.09.09 18:40:48 Client Debug Sending SOLICIT(opts:1 25 8 16 15 11 11 6 ) on eth0.832/10 to multicast.
2018.09.09 18:40:48 Client Debug Sleeping for 4 second(s).
2018.09.09 18:40:52 Client Info Processing msg (SOLICIT,transID=0x6359e9,opts: 1 25 8 16 15 11 11 6)
2018.09.09 18:40:52 Client Error AUTH: protocol 6529048 not supported yet.
2018.09.09 18:40:52 Client Debug Sending SOLICIT(opts:1 25 8 16 15 11 11 6 ) on eth0.832/10 to multicast.
2018.09.09 18:40:52 Client Debug Sleeping for 8 second(s).
2018.09.09 18:41:00 Client Info Processing msg (SOLICIT,transID=0x6359e9,opts: 1 25 8 16 15 11 11 6)
2018.09.09 18:41:00 Client Error AUTH: protocol 6529048 not supported yet.
2018.09.09 18:41:00 Client Debug Sending SOLICIT(opts:1 25 8 16 15 11 11 6 ) on eth0.832/10 to multicast.
2018.09.09 18:41:00 Client Debug Sleeping for 16 second(s).
2018.09.09 18:41:16 Client Info Processing msg (SOLICIT,transID=0x6359e9,opts: 1 25 8 16 15 11 11 6)
2018.09.09 18:41:16 Client Error AUTH: protocol 6529048 not supported yet.
2018.09.09 18:41:16 Client Debug Sending SOLICIT(opts:1 25 8 16 15 11 11 6 ) on eth0.832/10 to multicast.
2018.09.09 18:41:16 Client Debug Sleeping for 32 second(s).
cat /etc/dibbler/radvd.sh
#!/bin/bash
if [ "$SRV_MESSAGE" != "REPLY" ]
then
exit 1
fi
function fullPrefix () {
local input=$1
local o=""
local z=""
input=$(tr 'A-F' 'a-f' <<< $input )
while [ "$o" != "$input" ]; do
o="$input"
input="$( sed 's|:\([0-9a-f]\{3\}\):|:0\1:|g' <<< "$input" )"
input="$( sed 's|:\([0-9a-f]\{3\}\)$|:0\1|g' <<< "$input" )"
input="$( sed 's|^\([0-9a-f]\{3\}\):|0\1:|g' <<< "$input" )"
input="$( sed 's|:\([0-9a-f]\{2\}\):|:00\1:|g' <<< "$input" )"
input="$( sed 's|:\([0-9a-f]\{2\}\)$|:00\1|g' <<< "$input" )"
input="$( sed 's|^\([0-9a-f]\{2\}\):|00\1:|g' <<< "$input" )"
input="$( sed 's|:\([0-9a-f]\):|:000\1:|g' <<< "$input" )"
input="$( sed 's|:\([0-9a-f]\)$|:000\1|g' <<< "$input" )"
input="$( sed 's|^\([0-9a-f]\):|000\1:|g' <<< "$input" )"
done
grep -qs "::" <<< "$input"
if [ "$?" -eq 0 ]; then
GRPS="$( sed 's|[0-9a-f]||g' <<< "$input" | wc -m )"
((GRPS--)) # carriage return
((MISSING=8-GRPS))
for ((i=0;i<$MISSING;i++)); do
z="$z:0000"
done
input="$( sed 's|\(.\)::\(.\)|\1'$z':\2|g' <<< "$input" )"
input="$( sed 's|\(.\)::$|\1'$z':0000|g' <<< "$input" )"
input="$( sed 's|^::\(.\)|'$z':0000:\1|g;s|^:||g' <<< "$input" )"
fi
echo "$input"
}
SWITCH0_SUFFIX="01::1"
STATUS_FILE=/run/dibbler.lease
if [ -f "$STATUS_FILE" ];
then
source $STATUS_FILE
fi
TRIM_SIZE=17
FULLPREFIX=$( fullPrefix $PREFIX1 )
PREFIX1=${FULLPREFIX:0:TRIM_SIZE}
if [ "$PREFIX1" != "$CURRENT_PREFIX1" ]
then
if [ "$CURRENT_PREFIX1" != "" ]
then
ip addr delete "$CURRENT_PREFIX1$SWITCH0_SUFFIX/64" dev switch0
fi
echo "CURRENT_PREFIX1=$PREFIX1" > $STATUS_FILE
ip addr add "$PREFIX1$SWITCH0_SUFFIX/64" dev switch0
service radvd restart >/dev/null 2>&1
fi
cat /etc/dibbler/client.conf
# Defaults for dibbler-client.
# installed at /etc/dibbler/client.conf by the maintainer scripts
# 8 (Debug) is most verbose. 7 (Info) is usually the best option
log-level 8
duid-type duid-ll
# To perform stateless (i.e. options only) configuration, uncomment
# this line below and remove any "ia" keywords from interface definitions
# stateless
downlink-prefix-ifaces "none"
script "/etc/dibbler/radvd.sh"
iface eth0.832 {
pd
option 16 hex 00:00:04:0e:00:05:73:61:67:65:6d
option 15 hex 00:2b:46:53:56:44:53:4c:5f:6c:69:76:65:62:6f:78:2e:49:6e:74:65:72:6e:65:74:2e:73:6f:66:74:61:74:68:6f:6d:65:2e:6c:69:76:65:62:6f:78:34
option 11 hex 00:00:00:00:00:00:00:00:00:00:00:66:74:69:2f:74:63:32:66:67:65:32
option 11 hex 00:00:00:00:00:00:00:00:00:00:00:66:74:69:2f:74:63:32:66:67:65:32
option dns-server
}
../..