Linux :
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd081]
[ 0.000000] Linux version 5.4.154 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16325-88151b8303)) #0 SMP Sun Oct 24 09:01:35 2021
[ 0.000000] Machine model: Marvell 8040 MACCHIATOBin Single-shot
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 16 pages/cpu s26648 r8192 d30696 u65536
[ 0.000000] Detected PIPT I-cache on CPU0
[ 0.000000] CPU features: detected: EL2 vector hardening
[ 0.000000] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1031688
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk1p2 rw rootwait
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0xbc000000-0xc0000000] (64MB)
[ 0.000000] Memory: 4036316K/4192256K available (7294K kernel code, 428K rwdata, 1172K rodata, 448K init, 279K bss, 155940K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f022f000
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:160, num:32)
[ 0.000000] GICv2m: range[mem 0xf0280000-0xf0280fff], SPI[160:191]
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:192, num:32)
[ 0.000000] GICv2m: range[mem 0xf0290000-0xf0290fff], SPI[192:223]
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:224, num:32)
[ 0.000000] GICv2m: range[mem 0xf02a0000-0xf02a0fff], SPI[224:255]
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:256, num:32)
[ 0.000000] GICv2m: range[mem 0xf02b0000-0xf02b0fff], SPI[256:287]
[ 0.000000] random: get_random_bytes called from 0xffffffc0108d0bf8 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[ 0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[ 0.000082] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.000087] pid_max: default: 32768 minimum: 301
[ 0.000149] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.000167] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.000687] ASID allocator initialised with 32768 entries
[ 0.000717] rcu: Hierarchical SRCU implementation.
[ 0.000922] smp: Bringing up secondary CPUs ...
[ 0.001200] Detected PIPT I-cache on CPU1
[ 0.001225] CPU1: Booted secondary processor 0x0000000001 [0x410fd081]
[ 0.001526] Detected PIPT I-cache on CPU2
[ 0.001547] CPU2: Booted secondary processor 0x0000000100 [0x410fd081]
[ 0.001843] Detected PIPT I-cache on CPU3
[ 0.001858] CPU3: Booted secondary processor 0x0000000101 [0x410fd081]
[ 0.001890] smp: Brought up 1 node, 4 CPUs
[ 0.001899] SMP: Total of 4 processors activated.
[ 0.001903] CPU features: detected: 32-bit EL0 Support
[ 0.001906] CPU features: detected: CRC32 instructions
[ 0.001932] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.001934] CPU: All CPU(s) started at EL2
[ 0.001947] alternatives: patching kernel code
[ 0.004068] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.004077] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.004122] pinctrl core: initialized pinctrl subsystem
[ 0.004425] NET: Registered protocol family 16
[ 0.004777] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.005009] cpuidle: using governor ladder
[ 0.010931] cryptd: max_cpu_qlen set to 1000
[ 0.011971] SCSI subsystem initialized
[ 0.012118] usbcore: registered new interface driver usbfs
[ 0.012134] usbcore: registered new interface driver hub
[ 0.012150] usbcore: registered new device driver usb
[ 0.012299] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.012636] clocksource: Switched to clocksource arch_sys_counter
[ 0.012836] thermal_sys: Registered thermal governor 'step_wise'
[ 0.013169] NET: Registered protocol family 2
[ 0.013311] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.014279] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.014310] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.014440] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[ 0.014692] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.014756] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.014806] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.014912] NET: Registered protocol family 1
[ 0.014925] PCI: CLS 0 bytes, default 64
[ 0.015450] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 0.017195] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.017199] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.017630] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.018950] debugfs: Directory 'dummy-system-controller@440000' with parent 'regmap' already present!
[ 0.019093] armada-ap806-pinctrl f06f4000.system-controller:pinctrl: registered pinctrl driver
[ 0.019393] armada-cp110-pinctrl f2440000.system-controller:pinctrl: registered pinctrl driver
[ 0.019590] armada-cp110-pinctrl f4440000.system-controller:pinctrl: registered pinctrl driver
[ 0.021782] mv_xor_v2 f0400000.xor: Marvell Version 2 XOR driver
[...]
[ 0.023269] mv_xor_v2 f46c0000.xor: Marvell Version 2 XOR driver
[ 0.023347] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.023942] printk: console [ttyS0] disabled
[ 0.044076] f0512000.serial: ttyS0 at MMIO 0xf0512000 (irq = 8, base_baud = 12500000) is a 16550A
[ 0.688412] printk: console [ttyS0] enabled
[ 0.713017] f2702100.serial: ttyS1 at MMIO 0xf2702100 (irq = 27, base_baud = 15625000) is a 16550A
[ 0.742342] f4702000.serial: ttyS2 at MMIO 0xf4702000 (irq = 28, base_baud = 15625000) is a 16550A
[ 0.751589] omap_rng f2760000.trng: Random Number Generator ver. 203b34c
[ 0.751897] random: fast init done
[ 0.758413] omap_rng f4760000.trng: Random Number Generator ver. 203b34c
[ 0.761754] random: crng init done
[ 0.768551] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.779106] loop: module loaded
[ 0.782261] Loading iSCSI transport class v2.0-870.
[ 0.787472] ahci f2540000.sata: f2540000.sata supply ahci not found, using dummy regulator
[ 0.795807] ahci f2540000.sata: f2540000.sata supply phy not found, using dummy regulator
[ 0.804141] platform f2540000.sata:sata-port@0: f2540000.sata:sata-port@0 supply target not found, using dummy regulator
[ 0.815159] platform f2540000.sata:sata-port@1: f2540000.sata:sata-port@1 supply target not found, using dummy regulator
[ 0.826220] ahci f4540000.sata: f4540000.sata supply ahci not found, using dummy regulator
[ 0.834540] ahci f4540000.sata: f4540000.sata supply phy not found, using dummy regulator
[ 0.842846] platform f4540000.sata:sata-port@0: f4540000.sata:sata-port@0 supply target not found, using dummy regulator
[ 0.863272] spi-nor spi4.0: w25q32 (4096 Kbytes)
[ 0.868494] libphy: Fixed MDIO Bus: probed
[ 0.872884] libphy: orion_mdio_bus: probed
[ 0.877607] mvpp2 f2000000.ethernet: using 8 per-cpu buffers
[ 0.888959] mvpp2 f4000000.ethernet: using 8 per-cpu buffers
[ 0.901261] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[...] // Plein de trucs concernant l'USB...
[ 1.064876] usbcore: registered new interface driver usb-storage
[ 1.071118] armada38x-rtc f4284000.rtc: registered as rtc0
[ 1.076738] i2c /dev entries driver
[ 1.081067] debugfs: Directory 'dummy-system-controller@400000' with parent 'regmap' already present!
[ 1.090559] sdhci: Secure Digital Host Controller Interface driver
[ 1.096771] sdhci: Copyright(c) Pierre Ossman
[ 1.101203] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.132252] mmc0: SDHCI controller on f06e0000.sdhci [f06e0000.sdhci] using ADMA 64-bit
[ 1.169864] mmc1: SDHCI controller on f2780000.sdhci [f2780000.sdhci] using ADMA 64-bit
[ 1.178539] NET: Registered protocol family 10
[ 1.183304] Segment Routing with IPv6
[ 1.187004] NET: Registered protocol family 17
[ 1.191477] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.204536] 8021q: 802.1Q VLAN Support v1.8
[ 1.211429] armada8k-pcie f2600000.pcie: host bridge /cp0/pcie@f2600000 ranges:
[ 1.218796] armada8k-pcie f2600000.pcie: MEM 0xc0000000..0xdfffffff -> 0xc0000000
[ 1.256442] mmc0: new high speed MMC card at address 0001
[ 1.262112] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB
[ 1.266797] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB
[ 1.272878] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB
[ 1.278853] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB, chardev (249:0)
[ 1.296529] mmc1: new SDHC card at address e624
[ 1.301302] mmcblk1: mmc1:e624 SU08G 7.40 GiB
[ 1.308992] mmcblk1: p1 p2
[ 2.222637] armada8k-pcie f2600000.pcie: Phy link never came up
[ 2.228581] armada8k-pcie f2600000.pcie: Link not up after reconfiguration
[ 2.235536] armada8k-pcie f2600000.pcie: PCI host bridge to bus 0000:00
[ 2.242178] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.247690] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xdfffffff]
[ 2.254607] pci 0000:00:00.0: [11ab:0110] type 01 class 0x060400
[ 2.260652] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 2.266986] pci 0000:00:00.0: supports D1 D2
[ 2.271272] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.278701] pci 0000:00:00.0: BAR 0: assigned [mem 0xc0000000-0xc00fffff]
[ 2.285523] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 2.854221] pcieport 0000:00:00.0: AER: enabled with IRQ 39
[ 2.859956] ahci f2540000.sata: f2540000.sata supply ahci not found, using dummy regulator
[ 2.868286] ahci f2540000.sata: f2540000.sata supply phy not found, using dummy regulator
[ 2.876545] platform f2540000.sata:sata-port@0: f2540000.sata:sata-port@0 supply target not found, using dummy regulator
[ 2.887496] platform f2540000.sata:sata-port@1: f2540000.sata:sata-port@1 supply target not found, using dummy regulator
[ 2.899519] ahci f2540000.sata: masking port_map 0x3 -> 0x3
[ 2.905149] ahci f2540000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 2.913714] ahci f2540000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 2.922189] scsi host0: ahci
[ 2.925255] scsi host1: ahci
[ 2.928208] ata1: SATA max UDMA/133 mmio [mem 0xf2540000-0xf256ffff] port 0x100 irq 40
[ 2.936167] ata2: SATA max UDMA/133 mmio [mem 0xf2540000-0xf256ffff] port 0x180 irq 40
[ 2.944218] ahci f4540000.sata: f4540000.sata supply ahci not found, using dummy regulator
[ 2.952539] ahci f4540000.sata: f4540000.sata supply phy not found, using dummy regulator
[ 2.960802] platform f4540000.sata:sata-port@0: f4540000.sata:sata-port@0 supply target not found, using dummy regulator
[ 2.971850] platform f4540000.sata:sata-port@1: f4540000.sata:sata-port@1 supply target not found, using dummy regulator
[ 2.984910] ahci f4540000.sata: masking port_map 0x3 -> 0x3
[ 2.990536] ahci f4540000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 2.999101] ahci f4540000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 3.007580] scsi host2: ahci
[ 3.010602] scsi host3: ahci
[ 3.013563] ata3: SATA max UDMA/133 mmio [mem 0xf4540000-0xf456ffff] port 0x100 irq 41
[ 3.021512] ata4: SATA max UDMA/133 mmio [mem 0xf4540000-0xf456ffff] port 0x180 irq 41
[ 3.029849] mvpp2 f2000000.ethernet: using 8 per-cpu buffers
[ 3.044117] mvpp2 f2000000.ethernet eth0: Using firmware node mac address 00:51:82:11:22:00
[ 3.060971] mvpp2 f4000000.ethernet: using 8 per-cpu buffers
[ 3.078208] mvpp2 f4000000.ethernet eth1: Using firmware node mac address 00:51:82:11:22:01
[ 3.088235] mvpp2 f4000000.ethernet eth2: Using firmware node mac address 00:51:82:11:22:02
[ 3.098258] mvpp2 f4000000.ethernet eth3: Using firmware node mac address 00:51:82:11:22:03
[ 3.126133] xhci-hcd f4500000.usb3: xHCI Host Controller
[ 3.131478] xhci-hcd f4500000.usb3: new USB bus registered, assigned bus number 5
[ 3.139051] xhci-hcd f4500000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 3.148333] xhci-hcd f4500000.usb3: irq 33, io mem 0xf4500000
[ 3.154170] xhci-hcd f4500000.usb3: xHCI Host Controller
[ 3.159504] xhci-hcd f4500000.usb3: new USB bus registered, assigned bus number 6
[ 3.167023] xhci-hcd f4500000.usb3: Host supports USB 3.0 SuperSpeed
[ 3.173625] hub 5-0:1.0: USB hub found
[ 3.177399] hub 5-0:1.0: 1 port detected
[ 3.181439] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.189698] hub 6-0:1.0: USB hub found
[ 3.193474] hub 6-0:1.0: 1 port detected
[ 3.198377] armada38x-rtc f4284000.rtc: setting system clock to 2021-11-02T16:16:01 UTC (1635869761)
[ 3.273839] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.284334] ata1: SATA link down (SStatus 0 SControl 300)
[ 3.365595] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.371038] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.388704] VFS: Mounted root (squashfs filesystem) readonly on device 179:26.
[ 3.396107] Freeing unused kernel memory: 448K
[ 3.422686] Run /sbin/init as init process
[ 3.550483] init: Console is alive
[ 3.611248] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.625555] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.634581] init: - preinit -
[ 4.097618] mvpp2 f2000000.ethernet eth0: configuring for inband/10gbase-kr link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.832958] F2FS-fs (loop0): Mounted with checkpoint version = 7942fa32
[ 8.839897] mount_root: switching to f2fs overlay
[ 8.846380] overlayfs: "xino" feature enabled using 32 upper inode bits.
[ 8.903600] EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
[ 8.919373] urandom-seed: Seeding with /etc/urandom.seed
[ 8.964817] procd: - early -
[ 9.480717] procd: - ubus -
[ 9.534099] procd: - init -
Please press Enter to activate this console.
[ 9.639394] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.645588] urngd: v1.0.2 started.
[ 9.653317] i2c i2c-1: Added multiplexed i2c bus 2
[...]
[ 9.687336] i2c i2c-1: Added multiplexed i2c bus 9
[ 9.692148] pca954x 1-0070: registered 8 multiplexed busses for I2C switch pca9548
[ 9.700135] libphy: SFP I2C Bus: probed
[ 9.704055] sfp sfp-eth0: Host maximum power 1.0W
[ 9.709088] libphy: SFP I2C Bus: probed
[ 9.713007] sfp sfp-eth1: Host maximum power 1.0W
[ 9.718086] libphy: SFP I2C Bus: probed
[ 9.721993] sfp sfp-eth3: Host maximum power 1.0W
[ 9.729205] xt_time: kernel timezone is -0000
[ 9.736447] PPP generic driver version 2.4.2
[ 9.740994] NET: Registered protocol family 24
[ 9.747581] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.762755] mvpp2 f2000000.ethernet eth0: configuring for inband/10gbase-kr link mode
[ 11.770933] br-lan: port 1(eth0) entered blocking state
[ 11.776199] br-lan: port 1(eth0) entered disabled state
[ 11.781601] device eth0 entered promiscuous mode
[ 11.790115] mvpp2 f4000000.ethernet eth2: PHY [f212a200.mdio-mii:00] driver [Marvell 88E1510]
[ 11.799875] mvpp2 f4000000.ethernet eth2: configuring for phy/sgmii link mode
[ 11.807720] br-lan: port 2(eth2) entered blocking state
[ 11.813040] br-lan: port 2(eth2) entered disabled state
[ 11.818466] device eth2 entered promiscuous mode
[ 11.823214] br-lan: port 2(eth2) entered blocking state
[ 11.828465] br-lan: port 2(eth2) entered forwarding state
[ 11.833965] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 11.843327] mvpp2 f4000000.ethernet eth3: configuring for inband/2500base-x link mode
[ 11.851857] br-lan: port 3(eth3) entered blocking state
[ 11.857126] br-lan: port 3(eth3) entered disabled state
[ 11.862574] device eth3 entered promiscuous mode
[ 11.867362] br-lan: port 3(eth3) entered blocking state
[ 11.872611] br-lan: port 3(eth3) entered forwarding state
[ 12.090355] mvpp2 f4000000.ethernet eth1: configuring for inband/10gbase-kr link mode
[ 12.812953] br-lan: port 2(eth2) entered disabled state
[ 12.818582] br-lan: port 3(eth3) entered disabled state
[ 16.013021] mvpp2 f4000000.ethernet eth2: Link is Up - 1Gbps/Full - flow control off
[ 16.020815] br-lan: port 2(eth2) entered blocking state
[ 16.026070] br-lan: port 2(eth2) entered forwarding state