Merci @zoc, rien ne t'échappe. 

What's new in 7.19 (2025-May-22 10:53):

*) arm64 - fixed possible transmit queue timeout on CCR2216, CCR2116, RDS2216;
*) arp - added warning, when "Published" ARP entry used on an interface with "reply-only" ARP mode enabled;
*) bgp - added input.filter-community;
*) bgp - fixed excessive CPU usage;
*) bgp - fixed input.accept-community;
*) bgp - fixed memory leak on receiving notify and closing session;
*) bgp - improved performance on BGP input;
*) bonding - added setting for LACP active/passive modes;
*) bridge - added new STP monitoring fields for bridge and ports (Tx/Rx BPDU, Tx/Rx TC, forward/discard transitions, last topology change, message-age, max-age, remaining-hops, bridge-id);
*) bridge - fixed bridge port hang when using invalid port IDs;
*) bridge - fixed dhcp-snooping in QinQ setups;
*) bridge - fixed issue when local MACs were removed unnecessarily;
*) bridge - fixed minor memory leak on link down;
*) bridge - fixed multicast packet flow on hardware offloaded bridge which acts as "multicast-router";
*) bridge - improved default bridge and port layout on console and GUI;
*) bridge - improved stability in case of configuration error (introduced in v7.15);
*) bridge - moved "TCHANGE" logs from bridge,stp to bridge,stp,debug;
*) bridge - offload VXLAN only if another HW offloaded port exists in the bridge;
*) bridge - properly flush bridge hosts when bonding is used as bridge port and loses hw-offloading status;
*) bridge - rename "ports" to "interface" under MDB table for configuration consistency with other menus;
*) bridge - renamed STP monitor fields (port-number to port-id, designated-port-number to designated-port-id, designated-bridge to designated-bridge-id);
*) bridge - show designated-* monitor field for all port roles;
*) bridge - show warning instead of causing error when using multicast MAC as admin-mac (introduced in v7.17);
*) bth - properly specify "in-interface" when adding dynamic firewall NAT rule;
*) capsman - fixed "undo" command for cap interfaces;
*) certificate - added built-in root certificate authorities store;
*) certificate - do not include CA identity in SCEP POST requests;
*) certificate - fixed cloud-dns challenge validation for sn.mynetname.net (CLI only);
*) certificate - improve error message when trying to use certificate;
*) certificate - optimize trust store;
*) cloud - fixed issues when BTH is toggled fast between enable/disable;
*) cloud - improved "BTH Files" web page design;
*) conntrack - improved stability on busy systems;
*) console - added on-error to "for" and "foreach" loops;
*) console - added proplist to monitor command;
*) console - disallow incomplete double-quoted arguments (allows multiline string pasting);
*) console - do not treat return values as errors in scripts run from scheduler;
*) console - enabled verbose error logging for non-scripted/non-verbose imports;
*) console - fixed issue with file-name completion (introduced in v7.18);
*) console - fixed issue with files when using scripts (introduced in v7.18);
*) console - fixed misaligned multiline in brief print mode;
*) console - improve time value handling;
*) console - improved file add/remove process stability;
*) console - print large number argument values in proper format in export output;
*) console - set "/system/note show-at-login=yes" the default value after configuration reset;
*) console - validate script arguments (do, on-error, etc.) and reject invalid values;
*) container - allow changing container name;
*) container - fixed repository name handling to prevent redirect issues when basic authentication is used;
*) container - try to derive a user readable container name from remote image or file;
*) defconf - added DHCP Client on RDS2216 MGMT interface;
*) defconf - increased PPP interface wait time;
*) device-mode - added new "rose" mode where "container" feature is enabled by default;
*) dhcpv4 - improved outgoing packet logging;
*) dhcpv4-client/server - added support for DHCPv4 reconfigure messages;
*) dhcpv4-server - "Relay-Agent-Information" (82) option moved at the end of option list in response packets;
*) dhcpv4-server - accept packets with htype 6;
*) dhcpv4/v6-client - added check-gateway parameter;
*) dhcpv4/v6-client - fixed default route when DHCP client interface is in VRF;
*) dhcpv6-client - allow selecting to which routing tables add default route;
*) dhcpv6-relay - clear saved routes on DHCP release;
*) dhcpv6-relay - show client address;
*) dhcpv6-server - allow unsetting prefix-pool for static bindings and show warning if prefix is not in selected prefix-pool;
*) dhcpv6-server - change bound status to waiting on binding disable;
*) dhcpv6-server - change static binding bound status to waiting on server disable;
*) dhcpv6-server - fix when expired static binding is declined with false "binding belongs to another server" reason;
*) dhcpv6-server - improved stability when disabled server have static bindings;
*) dhcpv6-server - improved stability when disabling server with active bindings;
*) disk - add "sector-size" property in print detail;
*) disk - add reset-counters to /disk btrfs filesystem;
*) disk - renamed "eject-drive" command to "eject" (CLI only);
*) disk - renamed "format-drive" command to "format" (CLI only);
*) dlna - improved folder indexing behavior;
*) dns - improved DNS server service stability;
*) dot1x - fixed dynamic switch ACL rules on boards with a lot of ports (e.g. CRS520);
*) ethernet - improved Ethernet and PoE port mapping to ensure a consistent and reliable interface order;
*) fetch - fixed false successful messages in FTP mode;
*) file - added show-hidden parameter to /file/print, allowing referencing and deleting hidden files;
*) file - fixed missing files from The Dude (introduced in v7.18);
*) file - improved responsiveness on slow filesystems;
*) firewall - always show "passthrough" when exporting mangle table;
*) firewall - detect VRF addresses as local;
*) firewall - fixed IP/Settings "ipv4-fasttrack-active" status showing as inactive when it is active;
*) health - hide settings in CLI if there is nothing to show;
*) health - improved performance on devices with simple voltage sensors;
*) hotspot - improvements to memory usage;
*) igmp-proxy - do not try to send leave message for multicast groups that the device itself has joined on the upstream interface (cosmetic fix for proxy error logs);
*) ike2 - improved initial key exchange process on slow or unreliable connections;
*) iot - improvement to LoRa dev-addr-validation behavior;
*) iot - improvement to LoRa join eui/net id filtering behavior;
*) iot - improvement to LoRa stability and functionality;
*) iot - improvement to LoRa whitelist/blacklist support;
*) iot - iot-bt-extra package stability improvement;
*) ip-service - show all TCP/UDP connections on the system;
*) ip-service - show all TCP/UDP ports on system, including ports in containers;
*) ip-service - show error message when service enable fails;
*) ippool6 - properly free IPv6 pool used prefix when it is not used any more;
*) ipsec - fixed system failure on MMIPS devices when using IPsec services;
*) ipsec - lower standalone cipher, hash priority when using ctr aead;
*) ipv6 - avoid watchdog reboot due to link-local IPv6 address reconfiguration on thousand of interfaces at once;
*) ipv6 - fixed EUI-64 false error message on address update when "from-pool" option is used;
*) isis - properly validate 3-way hello handshake;
*) l2tp-ether - improved stability when trying to connect to disabled L2TP server with IPsec;
*) l3hw - remove VLAN tag before VXLAN encapsulation (fixes pvid behavior for bridged VXLAN);
*) log - added additional CEF fields from firewall and login logs;
*) log - fixed remote logging after reboot when hostname is forwarded to a DNS server;
*) log - populate in/out fields in firewall CEF logs with correct data;
*) lte - added UICC parameter in LTE monitor for R11e-4G modem;
*) lte - additional fixes for eSIM management support;
*) lte - AT modems, improved redialing when modem lost connectivity without notifying host about APN status change;
*) lte - automatically enable roaming for known roaming only SIM/eSIM profiles;
*) lte - Chateau 5G R16 fix DHCP relay packet forwarding using LTE interface;
*) lte - deactivate current eSIM profile before activating new profile;
*) lte - fixed default APN for configless modems;
*) lte - fixed EC200A-EU APN authentication;
*) lte - fixed initialization for Neoway N75 modem;
*) lte - fixed initialization for R11e-LTE6 modem;
*) lte - fixed LTE passthrough activation issue when IPv6 APN is used;
*) lte - fixed LTE status update or possible crash when modem is unexpectedly removed from system;
*) lte - fixed MBIM modem recovery after modem unexpected restart;
*) lte - fixed modem recovery after firmware upgrade for R11e-LTE modem;
*) lte - fixed possible crash or missing IPv6 address on first APN activation when IPv6 capable APN is used;
*) lte - fixed Router Advertisement processing issue for AT modems when an APN with "ip-type=ipv6" was configured;
*) lte - improved dialer for EC200A-EU modem;
*) lte - improved R11e-LTE6 link recovery delay time after unexpected modem registration status changes;
*) lte - initial support for user settable modem redial timer;
*) lte - initialize Quectel modems as soon as they are ready after unexpected restart;
*) lte - reset internal link-recovery-timer on sim slot change;
*) lte - set apn profile name the same as apn if no name specified when creating the profile;
*) lte - show correct value for 5G SA "current-cellid";
*) net - remove support for automatic multicast tunneling (AMT) interface (introduced in v7.18);
*) netinstall - improved network socket re-opening when NIC status changes while running the server;
*) netinstall - provide warning if memory on installed router is full after installation;
*) netinstall - show warning when network configuration on PC might not be appropriate for installation;
*) netinstall-cli - check for other running Netinstall servers on startup;
*) netinstall-cli - clear old configuration before user script using "-s";
*) netinstall-cli - fixed issue with applying the branding package;
*) ospf - fixed "mismatch" typo in logs;
*) ospf - make auth-key parameter sensitive;
*) ovpn - properly match GCM hardware acceleration capabilities (introduced in v7.17);
*) ovpn-server - do not reset active connections when changing comment or name;
*) ovpn-server - fixed server start-up after a reboot;
*) ovpn-server - properly show "username" in log when authentication fails;
*) pimsm - fixed issue where own query caused querier detection;
*) poe-out - upgraded firmware for 802.3at/bt PSE controlled boards (the update will cause brief power interruption to PoE-out interfaces);
*) port - added support for Huawei E3372-325 variant (vendor-id="0x3566" device-id="0x2001");
*) port - added USB mode switch support for "huawei-alt-mode";
*) port - fixed KNOT BG77 modem port lost after RouterOS upgrade from previous versions;
*) port - improvements to KNOT BG77 modem port channel handling;
*) ppc - fixed VLAN TCP packet transmit on PPC devices;
*) profiler - improved process classification;
*) ptp - added "ptp" logging topic;
*) ptp - allow multiple instances;
*) ptp - fixed PTP on 2.5G links;
*) ptp - fixed PTP on QSFP ports for CRS326, CRS510, CRS520, CCR2216 devices;
*) queue - fixed system failure when CAKE kind queue was configured but queue type definition does not exist anymore (introduced in v7.18);
*) queue - speed-up queue addition/removal process;
*) quickset - improved system stability;
*) rose-storage - added Btrfs disk balance command (CLI only);
*) rose-storage - added degraded Btrfs mount option (CLI only);
*) rose-storage - fixed mounting Btrfs subvolumes using macOS SMB client;
*) rose-storage - fixes for Btrfs;
*) rose-storage - improved system stability when removing NVMe disks;
*) rose-storage - rename default RAID device name from "raid" to "raid-array";
*) rose-storage - show Btrfs balance and scrub errors if any;
*) route - added options to set dynamic-in and connected-in chains in /routing/settings;
*) route - fixed stuck output when calling prints from multiple routing menus;
*) route - fixed route rule "min-prefix" unset;
*) route - improve stability on BGP reconnect;
*) route - make AFI naming consistent;
*) route - show "routing-table" by default on console print output;
*) route - show BGP session name instead of cache-id;
*) route-filter - fixed the "blackhole" option setting process;
*) route-filter - improved performance;
*) sfp - added sfp-encoding data output from EEPROM;
*) sfp - improved QSFP link stability for CRS354 devices;
*) sniffer - add max-packet-size (2k-64k) setting to be able to sniffer more than 2k data per packet;
*) snmp - fixed v2 getnext noSuchName error when OID with requested key does not exist;
*) ssh - fixed authorization with SSH key when multiple user SSH public keys are imported;
*) ssl/tls - respond with more precise alert error messages;
*) ssl/tls - send certificate authority in Certificate message even if it is not trusted;
*) switch - do not count rx-too-long multiple times on 100Gbps QSFP28;
*) switch - fixed egress mirroring for packets coming from external CPU port (e.g. CRS520, CCR2216, CCR2116);
*) switch - fixed switch name for hEX Refresh;
*) switch - flush CPU port FDB entries on switch disable;
*) switch - improve rate limit accuracy for MT7531, MT7621, EN7562CT;
*) switch - improved boot stability on devices with Alpine CPU and switch chip;
*) switch - improved stability when enabling IGMP snooping with VXLAN (introduced in v7.18);
*) switch - properly match IPv6 packets with empty ACL rule on CRS3xx, CRS5xx, CCR2004, CCR2116, CCR2216, RDS devices;
*) system - fixed "/system reboot" when the system disk is completely full;
*) system - improved internal "flash/" prefix handling for different file path related settings;
*) system - improved system stability when sending TCP data from the router;
*) system – added new "switch-marvell" and "wifi-mediatek" packages to support upcoming products;
*) timezone - updated timezone information from "tzdata2025b" release;
*) torch - improved data reporting;
*) upgrade - improved free disk space calculation;
*) upgrade - improved upgrade procedure reliability;
*) vrrp - fixed detection of connection tracking after reboot (introduced in v7.17);
*) vxlan -improved system stability when using IPv6 VTEP;
*) webfig - allow table column resize over side toolbar;
*) webfig - don't reorder rows when selecting header cells with Alt+click;
*) webfig - show IPv6 firewall connections;
*) webfig - show missing data in "IP/DNS/Cache" records;
*) wifi - add channel.reselect-time parameter which allows to perform channel re-selection at given time of day (CLI only);
*) wifi - add information on CAP uptime and connection uptime in "Remote CAP" list;
*) wifi - added "eap-identity" to registration table;
*) wifi - added SSID to logs;
*) wifi - display error when trying to run snooper on interface which does not support wireless packet capture (sniffer);
*) wifi - fix authentication of clients which omit some RSN information at association;
*) wifi - fix incorrect info about current channel for station interfaces after AP has switched channel (introduced in v7.17);
*) wifi - fix possible snooper crash when parsing frames with malformed headers;
*) wifi - fixed 5GHz chain enumeration on Chateau PRO ax;
*) wifi - implement WPA2 PSK authentication with key derivation using SHA256 (CLI only);
*) wifi - improve parsing of captured frames which have nested flags in radiotap header;
*) wifi - improved stability for wifi interfaces;
*) wifi - improved stability when doing SNMP query;
*) wifi - improved wifi connection stability when used as a station for "b" mode access point;
*) wifi - re-word log entries about disconnections which are likely caused by peer using a wrong passphrase;
*) wifi - use at least TLS 1.2 for securing connection between CAPsMAN manager and CAPs;
*) wifi-qcom - fix inability of interfaces in station mode to connect if they do not support full bandwidth of AP;
*) wifi-qcom - fix OWE authentication for 802.11ac interfaces in station mode;
*) winbox - added "MAC Telnet" under "Wifi/Registration" menu;
*) winbox - added "Multi Passphrase Group" for wifi;
*) winbox - added "Reset MAC address" for legacy wireless and wifi;
*) winbox - added comment fields for WiFi "Multi Passphrase Group" menu;
*) winbox - added comment under "User Manager/Routers" menu;
*) winbox - added country to wireless setup-repeater;
*) winbox - added missing "Switch" menu for RDS;
*) winbox - added missing file systems for disk formatting;
*) winbox - added missing parameters for BTRFS related action functions;
*) winbox - added mount-point parameter under "Disk/Settings" menu;
*) winbox - added netmask support for switch rule Src/Dst IPv6 Address settings;
*) winbox - allow opening BTRFS menu entries;
*) winbox - changed default wireless wds-cost-range values;
*) winbox - do not show not relevant values for certificate template;
*) winbox - fixed "Multi Passphrase Group" setting for wifi;
*) winbox - fixed "registry-url" field under "Containers" configuration menu;
*) winbox - fixed missing SMB client on non-ROSE devices;
*) winbox - fixed several statistics counters not being read only;
*) winbox - fixed switch menu for Chateau 5G;
*) winbox - fixed time interval type fields precision under "Disks" menu;
*) winbox - hide container File/Remote Image fields only when instance added;
*) winbox - improve graphing efficiency when communicating with WinBox;
*) winbox - make BTRFS "Parent" and "Send Parent" options optional;
*) winbox - properly show/hide OSPF, RIP and BGP tabs for IPv6 routes;
*) winbox - renamed "raid-member" to "raid member" flag for consistency;
*) winbox - show eSIM profiles under eSIM menu without manual refresh;
*) wireguard - add wg-import config-string parameter to import config directly from terminal;
*) wireguard - update peer info on "get" command;
*) wireless - added "eap-identity" to registration table;
*) wireless - implement handling of RADIUS disconnect messages by CAPsMAN;
*) wireless - suggest all legitimate frequencies for interfaces with 20/40mhz-XX  channel width in GUI;
*) x86 - added support for Emulex NIC;
*) x86 - i40e updated driver to 2.27.8 version;
*) x86 - remove unnecessary console output on shutdown;

What's new in 7.19.2 (2025-Jun-20 10:55):

*) bfd - fixed socket leak;
*) bgp - fixed withdraw when input.accept-nlri is non-existent;
*) btest - properly close unsuccessful TCP test sockets;
*) console - added prompt to /disk/format command;
*) disk - do not allow to start Btrfs replace command when a Btrfs replace process is already running;
*) disk - improve disk file system detection;
*) hotspot - allow only "http:" and "https:" schemas in dst field;
*) iot - added LoRa interface recovery mechanism;
*) iot - LoRa stability improvement;
*) iot - LR8G/9G firmware update;

What's new in 7.19.4 (2025-Jul-28 13:00):

*) arm - improved system stability when processing encrypted traffic;
*) arm64 - increased maximum number of CPU cores to 128;
*) ethernet - improved ethernet stability when handling invalid packets on Alpine CPUs;
*) iot - fixed incorrectly set LoRa channel plan behavior;
*) ipv6 - fixed policy routing;
*) leds - fixed issues after changing "dark-mode" configuration (introduced in v7.19);
*) license - updated URL for "libcroco" package in the license notice;
*) log - output PoE-Out LLDP negotiation to poe,info topic;
*) net - ensure packet sockets from containers do not disable RouterOS fastpath/fasttrack;
*) netinstall-cli - recognize RouterOS v6 system package;
*) port - give "gps" prefix for R11e-LR8G and R11e-LR9G GPS ports;
*) ptp - allow priority1 value of 0 (improves stability when receiving announce messages with priority1 set to 0);
*) routing-filter - fixed route origin matcher;
*) system - improved system stability for CCR2216 device;
*) system - improved system stability when using fasttrack;

What's new in 7.20 (2025-Sep-29 12:33):

*) arm64/x86/chr - added Aquantia network driver;
*) bgp - added brief, unnumbered output for advertisements list;
*) bgp - added initial EVPN support;
*) bgp - added NLRI filter for more precise accept/discard of ipv4/6 prefixes;
*) bgp - automatically create output.network blackhole routes;
*) bgp - decode and log notifications;
*) bgp - fixed nexthop force-self for IPv4 and IPv6;
*) bgp - fixed selection of received BGP VPN routes;
*) bgp - improved configuration upgrade from versions prior to 7.20;
*) bgp - improved logging;
*) bgp - introduced BGP instance configuration (note, downgrading to earlier versions without instance support may cause config issues);
*) bgp - make "as" parameter optional in template configuration;
*) bgp - print aigp attribute in advertisements;
*) bgp - refresh WinBox when BGP session is created/deleted;
*) bgp - resend routes after nexthop-choice update;
*) bgp - support for Advertising IPv4 Network Layer Reachability Information (NLRI) with an IPv6 Next Hop;
*) bridge - added dynamic tagged entry named "switch-cpu" in scenarios where the same VLAN spans multiple switch chips or is used on both HW and SW ports;
*) bridge - added verbose STP debug logging (rx/tx BPDU, edge-port and port-role transitions, FDB flush);
*) bridge - added warning log when all MACs cannot be displayed under the host table;
*) bridge - disable/enable HW offload on bonding slave disable/enable (fixes potential MAC learning issue);
*) bridge - fixed MVRP leave indication;
*) bridge - fixed port-id when adding a new port in non-primary MLAG;
*) bridge - improved stability when disabling bridge with dynamic VLANs in MSTI;
*) bridge - refactored host learning logic in MLAG setups in order to make it more robust and predictable;
*) bth - added extra file-share functionality for use with apps;
*) bth - improved tunnel name in client config export;
*) bth,file - added direct file sharing from the WinBox Files menu;
*) certificate - added "Amazon Root CA 1" to built-in root certificate authorities store;
*) certificate - fixed ACME certificate usage after renewal;
*) certificate - improved stability after failed import;
*) certificate - trust built-in root certificate authority store after configuration reset;
*) chr - added Chelsio VF driver for PCIID 5803;
*) chr - improved virtio_net performance;
*) cloud - fixed restoring "BTH Files" service after a prolonged network outage;
*) cloud - reduced "BTH Files" ping interval dynamically upon failure;
*) console - added use-tz option to :timestamp command;
*) console - fixed :convert to=num on MIPSBE;
*) console - fixed incorrect multibyte to=num conversions;
*) console - fixed issue where file completion sometimes shows duplicates;
*) console - improved stability and visuals for /interface/wireless/snooper/snoop;
*) console - improved visuals for brief print when displaying large tables;
*) console - improved visuals for hexadecimal strings;
*) console - improved visuals for hiding sensitive commands;
*) console - include flags by default when printing to value;
*) console - prioritize directory specific parameters and hide rarely used ones in print autocomplete;
*) console - replace TAB characters with spaces when editing scripts and added tab-width user configuration in /console/settings;
*) console - unified string representation of ID values;
*) console - updated hints for some /file/print parameters;
*) console - use file name completions (and basic validation) for file output related parameters for export and print commands;
*) console - validate filenames upon addition (if enabled in /console/settings);
*) container - added "device" option to pass a device from /system/hardware menu to a container;
*) container - added /container/log menu, keep 100 messages per container;
*) container - added default print brief mode;
*) container - added initial support for container in container setups;
*) container - added option to execute commands inside a container using "/container/shell cmd= user=";
*) container - added per-container memory limiting and monitoring;
*) container - added repull command;
*) container - added SCTP support;
*) container - added support for cpuset, cpu, memory, pids cgroups;
*) container - allow picking passthrough devices by descriptive name;
*) container - allow read-only mounts;
*) container - allow to mount individual files, not just directories;
*) container - allow to specify multiple envlists;
*) container - allow to use multiple veths in a container, change the in container interface name to same as in RouterOS;
*) container - can use KVM (x86 and arm64) in container QEMU for faster virtualization;
*) container - display any error prominently in WinBox;
*) container - do not allow multiple containers with same root directory;
*) container - enable check-certificate by default for new remote imports;
*) container - fixed containers that use inotify interface;
*) container - fixed environment variables not being passed to "/container/shell" properly;
*) container - fixed QEMU VM to host bridge;
*) container - fixed shell exit causing freeze;
*) container - improved compatibility when running containers with custom "cmd" and "entrypoint" commands;
*) container - improved error and log messages;
*) container - prevent user from setting "root-dir=/" for a container;
*) container - show a more descriptive error when tar extraction fails, particularly "No space left on device";
*) container - show config.json to user;
*) container - show explicit stopped flag for container;
*) container - stability improvements;
*) container - support for direct access to hardware devices;
*) container - terminate containers on shutdown, allow them to clean up properly;
*) dhcp - show error only after interface status is synced with the system (instead of erroneously displaying it immediately);
*) dhcp-client - show warning if DHCP client is configured on dot1x server port;
*) dhcp-server - do not show "I" flag when server is disabled;
*) dhcp-server - improved logging when dual-stack is enabled but fails to acquire client MAC from DUID;
*) dhcpv4-client - allow specifying DSCP of outgoing packets;
*) dhcpv4-client - allow specifying vlan-priority of outgoing packets (for VLAN interfaces only);
*) dhcpv4-client - show "custom-hostname-suffix" and "custom-source-mac-address" properties if set;
*) dhcpv4-server - added "add dns" step to setup wizard;
*) dhcpv4-server - added "lease-agent-circuit-id" and "lease-agent-remote-id" variables to the lease script;
*) dhcpv4-server - added "ntp-none" parameter;
*) dhcpv4-server - changed the default value of address-pool to "static-only" in the option matcher, removed "none" option;
*) dhcpv4/v6-client - properly resume client service after underlying interface status changes;
*) dhcpv4/v6-server - added CoA support;
*) dhcpv6-client - added "accept-prefix-without-address" allowing client to accept prefix when address is not available although requested;
*) dhcpv6-client - update the routing table and address list on manual client configuration changes;
*) dhcpv6-server - added "ignore-ia-na-bindings" setting that allows server to ignore address requests and work just with prefixes;
*) dhcpv6-server - do not trim real client DUID when assigning it to the binding;
*) discovery - disable discovery on loopback, LTE, ppp-out interfaces;
*) discovery - improved LLDP Power via MDI TLV with 802.3bt specific field support;
*) discovery - output LLDP fault message once per port poe-out status change;
*) discovery - report router as "CAPsMAN" on MNDP under "running" parameter;
*) discovery - set initial poe-out Tx power above 0dW;
*) disk - allow to format multiple disks at once;
*) disk - allow to remove Btrfs device by ID;
*) disk - better manage disks disappearing from RAID;
*) disk - cleanup mountpoint when setting mount-filesystem=no;
*) disk - disallow adding SMB share or user with empty name;
*) disk - do Btrfs remove-device asynchronously;
*) disk - offer to blink only PCI slots in console;
*) disk - rename raid-role=unspecified to spare;
*) disk - reset RAID role of old disk after spare assumes a new role;
*) disk - show error when file based block-device uses a mountpoint to be unmounted;
*) disk - show total/free inode counts for fs's that support it;
*) dlna - recognize flac extension;
*) dns - fixed memory leak when static CNAME record was matched;
*) fetch - display file sizes between 1-1023 bytes as 1KiB (instead of 0KiB);
*) fetch - include RouterOS version in the "User-Agent" field;
*) file - improved file handling performance in WinBox v4;
*) filesystem - improved calculation of free space on NAND flash (fixes potential "disk is too small" issue);
*) firewall - added "liberal-tcp-tracking" connection tracking setting;
*) firewall - added connection tracking "total-ip4-entries" and "total-ip6-entries" counters;
*) firewall - allow "dst-limit" matcher to work properly above value 10000;
*) firewall - fixed IPv6 firewall interface matchers not matching VRF interfaces;
*) firewall - improved IPv6 connection tracking lookup responsiveness;
*) firewall - improved system stability when processing connections on multicore systems;
*) firewall - reorganized firewall connection tracking table values and make them persistent between IPv4 and IPv6;
*) flashfig - bind to local address (fixes issue when multiple interfaces are enabled);
*) iot - added additional dongle firmwares to iot-bt-extra package;
*) iot - added an option to increase the amount of LoRa's traffic entries displayed;
*) iot - added support for MQTT last will message;
*) iot - adjusted default LoRa antenna gain values for specific devices;
*) iot - fixed an issue where channel #7 is ignored during LoRa LNS connection;
*) iot - fixed logic for unknown NetIDs;
*) iot - fixed support for LoRa Alliance NetID list;
*) iot - improved LoRa stability and error recovery;
*) iot - improvement to LoRa band verification logic;
*) iot - iot-bt-extra package stability improvement and additional dongle support;
*) iot - LoRa netid filters now can be configured as a "range";
*) iot - LoRa server list is no longer generated if the LR card is not physically attached;
*) iot - LR8G/9G firmware update;
*) iot - removed lora-package, LoRa functionality was moved into iot-package;
*) iot - removed non-existent GPIO pin functionality;
*) ip - added socksify feature and new NAT action "socksify";
*) ip-service - show service name "nfs" for port 2049;
*) ipsec - fixed degraded IPsec performance for IPQ-6010 (introduced in v7.17);
*) ipsec - move raw RSA keys to /ip/ipsec/key/rsa;
*) ipv6 - added support for IPv6 ND proxying of individual addresses;
*) ipv6 - do not allow removal of dynamic address on lo interface;
*) ipv6 - fixed "auto-link-local" feature on WireGuard interface;
*) ipv6 - make pref-src work and settable for static routes;
*) isis - added passive parameter for interface templates;
*) log - added command to clear memory action entries;
*) log - improved the "transmit loop detected" warning log;
*) lte - added "done" status for modem firmware-upgrade version check;
*) lte - added "remove-sent-sms-after-send" option to automatically delete sent SMS messages;
*) lte - added log entry if eSIM has no profiles on read;
*) lte - added modem-init string response to system log;
*) lte - added passthrough support for RG650E-EU modem;
*) lte - added show-capabilities eSIM presence detection for MBIM modems;
*) lte - allow only one IPv6 APN for AT modems;
*) lte - display ICCID regardless of SIM PIN entry status;
*) lte - do not reconfigure modem if deactive eSIM profile is deleted;
*) lte - exempt eSIM provision from global CRL certificate settings;
*) lte - exit LTE scan if modem reconfigured;
*) lte - fallback to RA for global IPv6 if unattained via AT channel (resets on config change);
*) lte - fixed inappropriate LTE interface inactive flag shown during modem initialization;
*) lte - fixed modem recovery on unexpected modem reboot for Chateau 5G and Chateau 5G R16;
*) lte - fixed progress message for R11e-LTE modem firmware-upgrade;
*) lte - fixed rare case where AT dialer could stop;
*) lte - improved EC200A-EU firmware-upgrade stability;
*) lte - improved SMS sending stability over MBIM protocol;
*) lte - refresh eSIM profile list after successful provision;
*) lte - renamed "uicc" to "iccid" in LTE monitor and eSIM profile print;
*) lte - show ip-type in /interface/lte/apn/print;
*) lte - use modem-supplied IPv6 address over EUI-64 when available;
*) macvlan - allow creating macvlan interfaces on all interfaces with a MAC address;
*) mpls - fixed minimal dynamic-label-range setting;
*) net - fixed possible slave flag issues after user configuration changes;
*) net - improved system stability when processing TCP/UDP connections;
*) net - prevent removal of lo interface via WinBox;
*) netinstall - added after-install controls (reboot after installation, shutdown after installation, none);
*) netinstall - alert on unreadable configuration scripts;
*) netinstall - detect inactive install interface;
*) netinstall - fixed install for PPC devices;
*) netinstall - fixed mutually exclusive checkbox behavior;
*) netinstall - show router and package architecture;
*) netinstall - warn user if not enough space on device;
*) netinstall-cli - added MAC filter option "--mac";
*) netinstall-cli - added multiple install option "-m";
*) netinstall-cli - improved client device architecture detection;
*) netwatch - added "early-success-detection" and "early-failure-detection" properties for ICMP probe;
*) netwatch - fixed date and time for stats;
*) ovpn - added support for sha384 hmac;
*) ovpn - improved tunnel setup speeds in configurations with large ammount of active OVPN clients;
*) partitions - fixed failure to repartition correctly from 32MB partition size;
*) partitions - hide partition menu on unsupported boards (without NAND);
*) partitions - limit minimal partition size to 60MB;
*) poe-out - added support for line-interactive and offline UPS on CRS320;
*) poe-out - firmware update for 802.3at capable boards (the update will cause brief power interruption to poe-out interfaces);
*) poe-out - firmware update for 802.3bt capable boards (the update will cause brief power interruption to poe-out interfaces);
*) poe-out - improved dual-signature detection on CRS320;
*) poe-out - improved short-circuit detection and reporting on CRS320;
*) poe-out - increased maximum power margin for all classes on CRS320;
*) port - added IPv6 support for "remote-access" tool;
*) port - improved port status handling at unexpected device removal;
*) ppp - added "dhcpv6-use-radius" PPP profile feature that enables "use-radius" option on dynamically created DHCPv6 servers;
*) ppp - added "remote-ipv6-prefix-reuse" PPP profile feature that allows to advertise same prefix on multiple VPN clients at the same time;
*) ppp - added DHCPv6 assigned prefix to address list when configured and received from RADIUS;
*) ppp - added dhcpv6-lease-time profile configuration property;
*) ppp - do not send initial echo request if keepalive-timeout=disabled;
*) ppp - improved system stability when closing connections;
*) pppoe-server - added accept-untagged=yes/no option to accept untagged traffic in combination with pppoe-over-vlan-rage property;
*) ptp - added PTP support for RDS2216 device;
*) ptp - removed delays between timestamping and packet transmission, improving PTP precision;
*) qos-hw - added mirror-buffers property and monitoring values;
*) radius - fixed issue with Session-Timeout attribute functionality;
*) romon - changed default "disabled=yes" to "disabled=no" under /tool/romon/port;
*) romon - improved error message;
*) route - added missing and remove unnecessary parameters from /ipv6/route menu;
*) route - afi naming consistency in logs;
*) route - attempt to clean up stuck routes in the routing table;
*) route - do not allow to modify dynamic routes;
*) route - fixed incorrectly set nexthop interfaces for BGP VPN routes;
*) route - fixed issue when route table is installed to kernel without fib setting;
*) route - fixed skipping updated destinations;
*) route - improved stability;
*) route - removed fib-reinstall;
*) route - update router ID when disabled address is removed;
*) routerboot - fixed boot MAC for CRS212 switch ("/system routerboard upgrade" required);
*) routing-filter - added filter-wizard (filter generator with v6-like syntax);
*) routing-filter - added sync command;
*) routing-filter - make "chain" and "list" parameters required when adding new item;
*) sfp - fixed low power mode pins on CRS326-4C+20G+2Q+ for optical QSFP modules;
*) sfp - fixed qsfp28 breakout disable;
*) sfp - improved initialization and linking for sfp28 on CRS518;
*) sfp - improved SFP handling for CRS418 device;
*) sfp - improved system stability with some GPON modules for CCR2004 and CCR2116 devices;
*) smips - reduced package size, removed hotspot feature and provide it as a separate package;
*) sniffer - added CPU number and fast-path status in per-packet comment;
*) sniffer - save packets in pcapng format, it now includes interface name the packet was sniffed on, packet direction and nanosecond timestamp resolution;
*) snmp - added SNMP OIDs for firewall connection tracking "total-entries", "total-ip4-entries" and "total-ip6-entries";
*) snmp - improved service stability when processing v3 requests;
*) snmp - set maximum message size to 4 KB;
*) ssh - improved stability on busy server;
*) ssh - show user public key fingerprint under /user/ssh-keys;
*) ssh/sftp - fixed session disconnects during file transfer;
*) ssl/tls - fixed SSL looping behavior when multiple different TLS connections were used;
*) supout - added certificate settings section;
*) supout - added IP Service section;
*) supout - added MPLS settings section;
*) supout - added VXLAN VTEP section;

Finalement nous avons la possibilité de configurer la QoS nécessaire pour Orange (et utile pour autres) dans le client DHCPv4/v6, plus besoin d'avoir un switch pour le faire. Avec des Mangle rules et cette nouvelle feature c'est bon.

/ip dhcp-client add dscp=48 interface=vlan-wan vlan-priority=6